Kelly KLS7230S Controller - Electro & Company Inc.

Kelly KLS7230S Controller

Regular price$285.00
/
Shipping calculated at checkout.

Services
Bluetooth
  • Free Shipping in Continental USA

Kelly KLS programmable motor controllers provide efficient, smooth and quiet controls for electric motorcycles, golf carts and go-carts; as well as industrial motor control. KLS controllers are mainly designed to solve noise problems of BLDC motor driving application. Compared to the traditional trapezoidal waveform control technology, this technique based on sinusoidal wave driving technology is to reduce the operation noise and 1/3 switching loss, which well meets the noise reduction and efficiency requirements in the application of DC brushless motors. It uses high power MOSFETs, SVPWM and FOC to achieve efficiencies of up to 99% in most cases. A powerful microprocessor brings in comprehensive and precise control to the controllers. It also allows users to adjust parameters, conduct tests, and obtain diagnostic information quickly and easily.

  • Motor Current Limit, 20 seconds boost: 300A
  • Motor Current Limit, continuous: 120A

Features

  • Intelligence with powerful microprocessor.
  • Synchronous rectification, ultra low drop, fast SVPWM and FOC to achieve very high efficiency.
  • Electronic reversing.
  • Voltage monitoring on 3 motor phases, bus, and power supply.
  • Voltage monitoring on voltage source 12V and 5V.
  • Current sense on all 3 motor phases.
  • Current control loop.
  • Hardware over current protection.
  • Hardware over voltage protection.
  • Configurable limit for motor current and battery current.
  • Low EMC.
  • LED fault codes
  • Battery protection: current cutback, warning and shutdown at configurable high and low battery voltage.
  • Rugged aluminum housing for maximum heat dissipation and harsh environment.
  • Rugged high current terminals, and rugged aviation connectors for small signal.
  • Thermal protection: current cut back, warning and shutdown on high temperature.
  • Configurable 60 degree or 120 degree hall position sensors.Controller can do auto_Identification angle for different degrees of hall sensors.
  • Configurable high pedal protection: the controller will not work if high throttle is detected at power on.
  • Current multiplication: Take less current from battery, output more current to motor.
  • Easy installation: 3-wire potentiometer will work.
  • Standard PC/Laptop computer to do programming.There is one more choice for customers to program KLS controller.Standard Tablet with Android OS to do programming.Need a Z-TEK USB TO RS232 cable for connecting the controller to App program in Tablet.
  • User program provided. Easy to use. No cost to customers.
  • Support motors with any number of poles.
  • Up to 70,000 electric RPM standard. (Electric RPM = mechanical RPM * motor pole pairs;Motor pole pairs=Motor poles/2).

Specs

  • Frequency of Operation: 20kHz.
  • Standby Battery Current: < 0.5mA.
  • 5V or 12V Sensor Supply Current: 40mA.
  • Controller supply voltage range: PWR, 18V to 90V for controllers rated equal or lower than 72V.
  • Supply Current, PWR, 30mA Typical.
  • Configurable battery voltage range, B+. Max operating range: 18V to 1.25*Nominal Voltage.
  • Standard Throttle Input: 0-5 Volts(3-wire resistive pot), 1-4 Volts(hall active throttle).
  • Throttle Input: 0-5 Volts. Can use 3-wire pot to produce 0-5V signal.
  • Main Contactor Coil Driver<2A.
  • Full Power Operating Temperature Range: 0℃ to 70℃(MOSFET temperature).
  • Operating Temperature Range: -40℃ to 100℃ (MOSFET temperature).
  • Max Battery Current: Configurable.

EMX PRE TUNE AVAILABLE FOR QS120, QS138

You may also like


Recently viewed